Stand setup and usage

Stand setup and usage

To attach the Wacom Cintiq Pro 22 stand, use the assembly instructions below. To attach another VESA-compliant stand, use the VESA mounting holes on the back of your Cintiq Pro.

Important: The Cintiq Pro 22 is designed to be used with Wacom Cintiq Pro 22 Stand, or another stand that complies with the VESA 100mm x 100mm standard. The Wacom Cintiq Pro 22 Stand is sold separately. Visit the Wacom eStore for more information.
Warning: Using this product without a stand may damage the ExpressKeys and cause injury due to instability during use. Please be sure to use this product with a stand as instructed.

Topics on this page

Illustration of the Wacom Cintiq Pro 22 mounted on the stand

Stand part names

Table 1
A
(also see Table 2)		 B
(also see Table 2)		 C D E F n/a n/a
Arm Base plate Pivot plate Soft cloth (supplied by customer) Arm protection bag Fixing bracket Screws Hex wrench


Table 2
A Arm Illustrated guide labeling the stand components and controls referenced in the table
B Base plate
1 Mounting cap
2 Rotation switch
3 Arm lock
4 Kensington Security Slot

Assemble the Wacom Cintiq Pro 22 Stand

  1. Place a soft cloth (D - supplied by customer) on a flat surface and place your Cintiq Pro screen-down on top of the cloth.
    2. Illustration of the pen display placed screen-side down on a soft cloth
  2. Screw the Pivot plate (C) into the VESA mounting holes on the back of the Cintiq Pro. Orient the pivot plate so the rounded tab is positioned toward the top edge of the device.
    3. Illustration of the pivot plate attached to the back of the pen display with the rounded tab oriented toward the top
  3. Place the Arm protection bag (E) on a flat surface and place the Arm (A) on top of the bag.
    4. Illustration of the stand arm placed on the arm protection bag
  4. Slide the Base plate (B) over the buttons on the Arm through the wider ends of the Base plate slots. Then move the Base plate upward until the buttons sit in the narrow ends of the slots. This will temporarily attach the Base plate to the Arm.
    5. Illustration of the base plate slid onto the stand arm through the wider slot openings
  5. Secure the Base plate to the Arm using all six screws.
    6. Illustration of the base plate secured to the stand arm using screws
  6. Remove the Mounting cap from the arm.
    7. Illustration of the mounting cap removed from the stand arm
  7. Slide the Pivot plate down onto the Arm until it is fully seated.
    8. Illustration of the pivot plate seated onto the stand arm
  8. Insert the Fixing bracket (F) into the opening on the mount and tighten the screw to secure it in place.
    9. Illustration of the fixing bracket inserted and secured in the stand mount
  9. Re-insert the Mounting cap into the arm until it snaps into place.
    10. Illustration of the mounting cap pushed back into the top of the stand arm
  10. Use the cable ties included with your Cintiq Pro to bundle the cables and route them through the openings behind the stand.
    11. Illustration of cables bundled and routed through openings behind the stand

Set the Cintiq Pro's angle and height

  1. Unlock the arm by pushing the Arm lock down.
    2. Illustration of the arm lock pushed down to unlock the stand
  2. Optionally adjust the angle of your Cintiq Pro (up to 45 degrees).
    3. Illustration of the pen display adjusted to a tilted working angle
  3. Lock the arm by pushing the Arm lock up.

Rotate your Cintiq Pro

  1. Push the Rotation switch down to enable the rotation.
    2. Illustration of the rotation switch pushed down to enable rotation
  2. Optionally rotate your Cintiq Pro (up to 40 degrees).
    3. Illustration of the pen display rotated on the stand
  3. When you return your Cintiq Pro to the upright position, push the Rotation switch up to lock it.
 | Do not share my information | Cookies | Terms of use | Privacy Policy